Resetting your Holosun EPS Carry red dot sight back to factory settings can be a useful tool for troubleshooting issues or simply starting fresh. The process is fairly straightforward and only requires a few simple steps. Begin with locating the reset button on the back of the sight. This small lever is often unmarked but can be easily identified by its position.
- For initiating a factory reset, you'll need to hold down the reset button for a period of time of approximately 5 seconds. You should see a changing illumination pattern on the sight indicating that the reset process is in progress.
- Once the process is complete, the display will return to its default behavior.
- The red dot sight is now reset to factory defaults. You can then proceed with configuring it according to your desired setup.
Be sure to always refer to the user manual for specific instructions and details regarding your Holosun EPS Carry red dot sight.
Returning Your Holosun EPS Carry to Basic Settings
Need to Modify your Holosun EPS Carry Optical back to its Default configuration? It's Straightforward. Here's how:
First, ensure the Hologram is Activated. Then, locate the Switch labeled "Mode".
Press and hold this Button for approximately 5 seconds.
You should Detect a series of Changes on the Display. This indicates that the Holosun is now Back to Factory Settings to its Basic configuration.
Once complete, release the Control. Your Holosun EPS Carry is now Ready with all settings at their Factory values.
Resetting the Holosun EPS Carry Red Dot Sight
The Holosun EPS Carry Red dot sight is a popular choice for concealed carry applications due to its compact size and durable construction. However, like any optical device, it may require periodic calibration. This can be easily accomplished by following these simple steps: First, locate the adjustment screws on the side of the sight. These are typically located near the battery compartment. Using a small screwdriver, carefully turn the screws to fine-tune the point of impact. Begin by making subtle adjustments and test fire the sight at various distances to ensure accuracy. Continue this process until you achieve a desired zeroing point.
- Keep in mind that the adjustment screws can be easily damaged if overtightened, so use caution when turning them.
- Ensure that the battery is fresh and properly installed before making any adjustments.
- In case you encounter difficulty zeroing your sight, consult the manufacturer's guide for further assistance or contact Holosun customer support.
Revert Factory Settings for Holosun EPS Carry
To reset your Holosun EPS Carry to its factory settings, you will need to navigate through the sight's menu system. First, power up the optic by engaging the switch located on the side of the unit. Next, utilize the adjustable buttons found upon the holographic display to access the settings menu. Within the menu, locate the "Factory Reset" option and select it using the designated button. The EPS Carry will then undergo a reset sequence, which may take more info a few moments. Once complete, your sight will be restored to its default configuration.
- Note: During the reset process, all user-configured settings will be erased.
Erase Your Holosun EPS Carry Effortlessly
Need to get your Holosun EPS Carry back to factory settings? It's easier than you think! Here are the simple steps you need to follow:
First, turn off your sight. Then, find the tiny reset button on the side of the sight. Use a small tool like a paperclip or a pin to press and depress the reset button for about 5 seconds. You'll know it worked when the display starts flashing.
- Wait the sight to cycle through its startup sequence. This might take a few moments.
- You've successfully reset your Holosun EPS Carry to its original settings!
Reinitialize a Holosun EPS Carry Red Dot
Need to acquire a freshstart/clean slate? Here's how it's done to re-establish default settings your Holosun EPS Carry Red Dot.
First, make sure the red dot is activated. Next, locate the tiny button on the left/right side of the sight's housing/body. Hold down this button continuously for a duration of 5 seconds/3 seconds. You should observe a flashing light/blinking indicator indicating that the reset process has begun/started. Keep holding/pressing the button until the light stops blinking/flashing. Release the button and your Holosun EPS Carry Red Dot is now Factory Rested.